Forklift trucks – test

WYNIK

#1. Qualification certificates:

a ) are valid indefinitely

b ) are timely with a validity period depending on the number of points obtained at the exam

c ) are timely with a period of validity in accordance with the provisions of the Regulation on the mode of verification of qualifications

d ) are valid for a period of 15 years

#2. When entering a sloping ramp with a lift truck with a load that limits visibility, the operator:

a ) uses the help of another person

b ) moves forward

c ) moves in reverse

d ) the answers a and b are correct

#3. When descending an inclined ramp with a front-end lift truck and its load, the operator:

a ) moves forward

b ) moves backwards

c ) exercise extreme caution

d ) the answer b and c is correct

#4. Unless otherwise specified in the forklift instructions, the minimum permissible thickness of the horizontal part of the fork measured near its corner (heel) is:

a ) 25 mm at a nominal thickness of 30 mm

b ) 55 mm with a nominal thickness of 60 mm

c ) 40 mm at a nominal thickness of 60 mm

d ) is always 50% of the nominal thickness of the fork

#5. The service brake should be checked by driving the lift truck and braking:

a ) forward

b ) backwards

c ) in both directions

d ) the brake is checked only by the maintenance man

#6. A glowing oil pressure light can indicate:

a ) too low a level of fluid in the brake system

b ) increased engine temperature

c ) oil pressure too low

d ) the answers a and c are correct

#7. Based on the load capacity diagram shown and the drawing, determine the maximum safe lifting height, of the load taken from direction A:

a ) 4860 mm

b ) 8820 mm

c ) 7070 mm

d ) 10820 mm

#8. The net weight of 1,000 liters of water is approx:

a ) 800 kg

b ) 900 kg

c ) 1000 kg

d ) 1100 kg

#9. Unless otherwise specified in the forklift instructions, the minimum permissible thickness of the horizontal part of the fork measured near its corner (heel) is:

a ) 27 mm at a nominal thickness of 30 mm

b ) 57 mm with a nominal thickness of 60 mm

c ) 25 mm at a nominal thickness of 30 mm

d ) is always 50% of the nominal thickness of the fork

#10. The “STOP safety switch” is used to:”

a ) emergency stop of the cart operation

b ) normal stopping of engine operation

c ) prevents unauthorized persons from starting the truck

d ) all answers are incorrect

#11. After completing the technical examination with a positive result, the UDT inspector:

a ) extends the validity of the operator's qualification certificate

b ) marks the device with a sticker, which is permission to use the device

c ) informs the user in writing in the maintenance log that he or she agrees to operate the equipment

d ) draws up a report on the activities performed and issues an administrative decision authorizing operation

#12. Unless otherwise specified in the forklift instructions, the minimum permissible thickness of the horizontal part of the fork measured near its corner (heel) is:

a ) 25 mm at a nominal thickness of 30 mm

b ) 57 mm with a nominal thickness of 60 mm

c ) 36 mm at a nominal thickness of 40 mm

d ) is always 50% of the nominal thickness of the fork

#13. In case of dangerous damage to a technical device or an accident, the operator:

a ) immediately notifies the UDT of the occurrence of the incident

b ) notifies the manufacturer of the equipment of the causes of the resulting event

c ) immediately repair the device and transfer it for further operation

d ) reports the device for repair

#14. Based on the load capacity diagram shown and the drawing, determine the maximum safe lifting height, of the load taken from direction A:

a ) 700 mm

b ) 1200 mm

c ) 4500 mm

d ) 1800 mm

#15. During the service brake test, the mast should be in position:

a ) the position of the mast does not matter

b ) tilted ,,on itself",c ) tilted

from each other""

d ) vertical

Zakończ test

Test: Forklifts

WYNIK

#1. Qualification certificates:

#2. When entering a sloping ramp with a lift truck with a load that limits visibility, the operator:

#3. When descending an inclined ramp with a front-end lift truck and its load, the operator:

#4. Unless otherwise specified in the forklift instructions, the minimum permissible thickness of the horizontal part of the fork measured near its corner (heel) is:

#5. The service brake should be checked by driving the lift truck and braking:

#6. A glowing oil pressure light can indicate:

#7. Based on the load capacity diagram shown and the drawing, determine the maximum safe lifting height, of the load taken from direction A:

#8. The net weight of 1,000 liters of water is approx:

#9. Unless otherwise specified in the forklift instructions, the minimum permissible thickness of the horizontal part of the fork measured near its corner (heel) is:

#10. The “STOP safety switch” is used to:”

#11. After completing the technical examination with a positive result, the UDT inspector:

#12. Unless otherwise specified in the forklift instructions, the minimum permissible thickness of the horizontal part of the fork measured near its corner (heel) is:

#13. In case of dangerous damage to a technical device or an accident, the operator:

#14. Based on the load capacity diagram shown and the drawing, determine the maximum safe lifting height, of the load taken from direction A:

#15. During the service brake test, the mast should be in position: